diffusion layer
英 [dɪˈfjuːʒən ˈleɪə(r)]
美 [dɪˈfjuʒən ler]
扩散层
双语例句
- Influence of the PTFE contents on the performance of the gas diffusion layer;
厚度和方块电阻是用于气体扩散层的碳纤维材料的两个重要性能参数。 - Effects of the microstructure of anode gas diffusion layer on mass transport and performance of DMFC
扩散层微观结构对DMFC阳极传质及性能的影响 - The overlap between diffusion layer of microband electrode array and its effect on chronoamperometric current were studied, and the shielding effect on microband-array electrode is discussed.
研究了微带阵列电极的扩散层交叠情况及其对计时电流的影响； - Microstructure of RE-B-Al Diffusion Layer of Armco Iron and the Formation Mechanism of Borides
工业纯铁稀土硼铝共渗的渗层组织及硼化物的形成机理 - Performance Testing and Analysis of Carbon Fiber Material Used in Gas Diffusion Layer
用于气体扩散层的碳纤维材料的性能测试与分析 - Nitriding and oxidation: diffusion layer and oxidation layer improve soldering resistance, adhesion resistance and crack resistance.
氮化扩散层和氧化层：可以提高模具耐溶损性、耐过烧性、耐粘着性和耐热裂性。 - The relationships of chronoamperometric current and diffusion layer with electrolysis time are discussed at microband electrode.
本文讨论了微带电极的计时电流、扩散层与时间的关系； - Analysis and design of AES diffusion layer
AES扩散层的分析及改进方案设计 - Effect of Rare Earths on Kinetics of Boron-Aluminizing of Armco Iron and computer Fitting Microstructure of RE-B-Al Diffusion Layer of Armco Iron and the Formation Mechanism of Borides
稀土对工业纯铁共渗硼铝动力学的影响及计算机拟合工业纯铁稀土硼铝共渗的渗层组织及硼化物的形成机理 - Influence of Diffusion Layer for Multilayer Monochromator
层间扩散对多层膜镜单色器性能的影响 - Water transport in diffusion layer and active layer are analyzed separately.
分别针对扩散层和催化层分析液态水的传递特点。 - The microstructure and the properties of nickel diffusion layer were also investigated.
同时，对扩散层的组织和性能进行了研究。 - The effects of PTFE content on the performance of the gas diffusion layer of oxygen electrode were studied.
研究了不同含量PTFE对氧电极气体扩散层性能的影响； - The phases and their distribution in diffusion layer were studied.
并应用X射线衍射及透射电镜测试方法，研究了渗钛层的相组成及相分布。 - The diffusion layer in stainless steel-low carbon steel composite wire was studied.
对不锈钢&钢复合线中的扩散层进行了研究。 - Rapid cooling after nitrocarburizing, martensite structure is obtained at the diffusion layer.
氮碳共渗后快冷，在渗层获得含氮碳的马氏体组织。 - The effect of the current density and fuel cell temperature, humidified temperature of cathode and anode, porosity of porous diffusion layer on the results mentioned above are discussed.
讨论了质子交换膜燃料电池运行电流密度和温度、阴极和阳极加湿温度、气体扩散层孔隙率等参数对以上结果的影响。 - The nitrided layer of pure iron consists of compound layer and diffusion layer.
纯铁渗氮层则由化合物层和扩散层组成。 - The characteristics of so-called silicon diffusion layer were analyzed through EPMA and hardness test.
通过成分分析（EPMA）和硬度测试，分析了硅扩散层的特征。 - The pore structure and morphology of gas diffusion layer were studied by mercury intrusion method and SEM.
用压汞分析法和SEM研究了气体扩散层的孔结构及形貌。 - The result indicates that, the interface is divided into the diffusion layer and chill solidified layer.
结果表明：电磁复合铸造高铬铸铁轧辊界面由扩散层和激冷凝固层组成； - The cracks maybe occured firstly in the diffusion layer of the plasma nitrided layer in erosion damage.
离子渗氮层在冲蚀破坏中可能首先在过渡层产生裂纹。 - The interface area consists of cast iron layer, mixed layer, diffusion layer and hard alloy.
铸铁硬质合金界面区域由4层组成，依次为铸铁层、混合层、扩散层和硬质合金层。 - The carbon diffusion layer is affected by concentration gradient of alloy elements and carbon, atom diffusion, the heat treatment and surfacing processes.
碳扩散层的形成受合金元素与碳的浓度梯度、原子扩散、热处理工艺和堆焊工艺等因素的影响； - Under the condition with stirring, dissolving quantity of pure Nb in Ti-Al alloy is related with melting time and temperature. Diffusion layer thickness and mass transport coefficient were calculated by Machlin model, and the relationship of dissolving quantity and time is obtained.
对于有电磁搅拌的过程，纯Nb在Ti-Al合金的溶解量与时间和温度有关，通过马奇林模型对扩散层厚度和扩散传质系数进行了计算，判断了溶解量与时间的关系。 - The intermetallic compounds at interface diffusion layer have a great influence on the overall performance of the material.
界面扩散层所生成的金属间化合物对材料的整体性能有着重要的影响。 - After the 600 ℃ heat treatment, the diffusion layer was appeared between the coating and substrate.
600℃热处理试验后，基体与涂层之间出现了扩散层。 - Based on these analyses, two improved algorithms aiming to diffusion layer of block cipher are presented.
在此基础上，提出了两种针对分组密码中扩散层的改进方案。 - The second part is mainly about the analysis and design of the diffusion layer in SPN cryptographic structure.
第二部分是对SPN密码结构的扩散层进行分析设计。 - TiN permeation layer was composed of external deposition layer and diffusion layer with evenly distributed TiN particles.
TiN渗镀层由TiN颗粒均匀分布的扩散层及表面TiN沉积层组成。